Saturday, October 15, 2022

Hp Printer Streaks When Printing

Don't Miss

Try Opening The Printer Troubleshooter

Fixing Vertical Bands, Lines, or Streaks in Copies or Scans | HP Printers | @HPSupport

To keep the ink from smearing, you can also try troubleshooting the problem using Windows 10 Printer Troubleshooter. Heres how:

  • Run the search box by pressing the Windows key followed by the S hotkey
  • Search for troubleshooter in the search box
  • Click on the Run this troubleshooter button to launch the troubleshooter displayed below.
  • Find and select your printer as the option to fix and then click on Next
  • Complete all the on-screen instructions from the troubleshooter
  • One: Remove The Print Cartridges

  • Turn on the HP Deskjet printer, lift the top cover, and wait while the print cartridges move to the center of the printer.
  • After the cartridges have moved to the center of the printer, unplug the power cord from the back of the printer.
  • Remove both print cartridges, and place them on their sides on a sheet of paper.
  • caution:Do not leave the print cartridges outside the printer for longer than 30 minutes. If a cartridge is left uncapped for too long, the ink will dry out and the cartridge will become unusable. Also, be careful not to get any ink on your hands or clothes.

    Five: Run A Clean Test

    HP Deskjet Toolbox

  • Double-click the HP Deskjet Toolbox shortcut on the desktop.
  • Click the Printer Services tab.
  • Click Clean the Print Cartridges. Follow the instructions that appear on the screen.
  • NormalBest

    Internal test from the printer

    note:Careful cleaning is usually enough to remove streaks from printed pages. However, it is possible to miss fibers or debris that might interfere with print quality. Repeat the cleaning procedure until the test printout is 100% clear and sharp.

    Don’t Miss: Laser Printer Compatible With Ipad

    Cleaning The Electrical Contacts Inside The Carriage Assembly

  • Look for fibers or other contaminants on the electrical contacts inside the carriage assembly. The contacts in the printer can be damaged if too much pressure is applied during the wiping process. If necessary, the contacts may be cleaned by wiping them very gently with a dry, lint-free cloth . Try to gently remove any visible debris within the carriage.

    warning:Make sure the printer power is turned off before cleaning inside the printer.

    Figure : Cleaning the contacts inside the printer

  • Reinsert both cartridges. On printers with cartridge latches, close the latch over the top of the cartridges.
  • 3.Close the top cover.
  • Plug the power cord into the power outlet.
  • Print a test page. If the problem persists, go to Procedure 2.
  • Why Are There Streaks Lines Or The Wrong Colors On My Print

    Solved: streaks in print on a B/W laserjet printer

    If your print-outs are streaky, faded, have lines on them that should not be there, or are otherwise poor in quality, this may be due to a problem with the printer or a low ink or toner supply.

    Fading text or images

    You may be running out of ink or toner. Check your ink or toner supply and buy a new cartridge if necessary.

    Streaks and lines

    If you have an inkjet printer, the print head may be dirty or partially blocked. Try cleaning the print head. See the printers manual for instructions.

    Wrong colors

    The printer may have run out of one color of ink or toner. Check your ink or toner supply and buy a new cartridge if necessary.

    Jagged lines, or lines are not straight

    If lines on your print-out that should be straight turn out jagged, you may need to align the print head. See the printers instruction manual for details on how to do this.

    Don’t Miss: How To Scan A Document Brother Printer

    Seven: Check For Defects On The Diagnostic Page

    Missing lines or streaked bars

    Figure : Example: the left ink cartridge shows a streaked bar – the ink cartridge is not functioning correctly

    Colors do not match the color on the ink cartridge label

    Figure : One of the bar colors is very different from the color dot on the ink cartridge

    Missing colors

    note:If printing in reserve mode, without all the ink cartridges installed, the patterns associated with the missing ink cartridge will also be missing.

    Figure : Missing colors

    Running Out Of A Particular Color

    If you run out of a specific color cartridge, your printer may begin to skip lines. This problem is straightforward to spot using the printers test page to find the missing color .

    All four cartridges are necessary to create the colors required in everyday printing. Running out of one color prevents the correct mixing of certain hues.

    As well as depleting a specific cartridge by repeated use of a single color, cartridges can become faulty and run out of color if stored flat for a prolonged period of time.

    Don’t Miss: How To Get Printer Back Online Hp

    Visual Chart To Identify And Troubleshoot Common Hp Laser Printer Image Defects

    Image defects are defined as image abnormalities such as repeating specks, bands, or streaks down the page. Most defects can be traced to damaged rollers, broken gears, dirty mirrors, defects in the toner cartridge, or other common causes

    This article describes the process of solving image related problems and clarifies the brief steps in the HP Image Problem Solving Table. Skip to the “circled” number from the table for a clearer understanding of the recommended action. If that action does not cure the image problem, return to the Image Problem Table for the next action step. If you have reached Step 14 , consider calling your local service company for help.

    The numbers below correspond to the numbers in the right column of the Image Problem Table.

    Solution Three: Check The Paper Type Settings

    Fixing Streaks and Lines in Scans, Copies, and Faxes | HP Officejet | @HPSupport
    • Windows:
    • From the software program you are printing from , click File, and then click Print.
    • Select the printer, and then click Properties or Preferences.The Properties or Preferences dialog box will open.
    • In the Properties dialog box, click the Paper/Quality tab.
    • From the Paper type drop-down list, click More.
    • Expand the list of Type is: options.
    • Expand each category of paper types until you find the paper type that you are using.
    • If the print quality issues are resolved after updating the paper type settings, then you do not need to continue troubleshooting.
    • If the print quality issues persist, continue to the next solution.
  • Mac OS X:
  • On the File menu in the software program that you are printing from , click Print.The Print dialog box will open.
  • From the Paper Size drop-down list, select the size of paper that you are using.
  • Open the Paper/Quality menu.
  • From the Media Type drop-down list, select the size type of media that you are using.
  • If the print quality issues are resolved after updating the paper type settings, then you do not need to continue troubleshooting.
  • If the print quality issues persist, continue to the next solution.
  • Also Check: Printing From Android To Hp Printer

    One: Print A Print Quality Report

  • From the Home screen on the printer control panel, touch the Dashboard stripat the top of the screen, or swipe the dashboard tab downward. The fulldashboard will display.
  • At the top of the Dashboard, touch the gear icon . The Setup menu will display.
  • On the Setup menu, scroll to and touch Reports. The Reports menu will display.
  • On the Reports menu, touch Print Quality Report. The Print Quality Report will print.
  • Examine the Print Quality Report for defects.Refer to the table below for examples of a Print Quality Report with no defects, and a Print Quality Report that shows vertical dark lines on the color bars.
    Example of a Print Quality Report with no defects Example of vertical dark lines on the Print Quality Report
  • If you see vertical dark lines on the color bars, continue to Step two: Align the printhead.
  • If you see any defects other than vertical dark lines, such as significant streaks or uneven colors, skip to Step three: Clean the printhead.
  • Laser Printer Hardware Issues

    A laser printer has several hardware components that could cause issues with print quality. One piece of hardware to check is the toner cartridge and drum assembly. Most laser printers include the drum with the toner cartridge. The drum itself can be defective, which results in toner misapplied to paper, or smudged toner due to too much toner applied to the paper. A defective drum can also cause print lines to appear on paper, often in the same place on each piece of paper. Multiple print lines can appear on paper, evenly spaced between each other.

    The toner cartridge itself may have toner “leaking” from it, causing excess toner to get on the paper and other parts of the laser printer. Leaking toner, in general, can make a mess on the paper and inside the printer.

    Another piece of hardware in a laser printer that causes issues is the fuser. It is the component that fuses, or adheres, the toner to adhere to the paper. When it is not fusing correctly, toner can become smudged on the paper if non-fused toner sticks to the rollers.

    In the case of a bad drum or leaking toner, it is best to replace the entire toner cartridge. If you suspect a bad fuser is at fault, it is best to have the laser printer serviced at a repair shop.

    Read Also: How To Install Canon Wireless Printer Without Cd

    Hp Latex 310 Dripping Streaks On Print

    HP Latex 300 Series

    I have an HP Latex 310, and when I walked into my office this morning, I noticed two lines in the print as if something had leaked and dripped onto the material. In the attached pictures, you can see the streaks and a closeup of where there appears to be condensation or a leak of some sort. When I tried to wipe the streaks, they smeared and appeared oily as if it was optimizer. Has anyone experienced this problem?

    #1 HiA lot is being posted about this problem – it’s not the optimiser or ink leaking – material is sticking to the top of the heaters and smears printed image and you can see it when printing exactly how it happens… Try to lower temp, increase vacuum or just pull down the beginning of vinyl with another vinyl…Cheers and good luck.

    #1 These marks can be from the Printhead running very close against the media. Check the printing process from start until it exits the curing area. Keep an eye for movement and check if the media especially in the print area may deform, buckle or stutter. Adjust heat if media buckles too much and is causing light strikes against the head it may be too hot. Adjust vacuum if media isn’t holding down . Do this during print in adjustments menu.

    Make sure media is travelling out from print area and through curing zone nice and flat. Weight/s may be needed or you may need to feed some of it out first before print.

    Solution Four: Check The Printer Driver

    Solved: Vertical lines in prints
    HP PCL 6 driver Default on install CD. Recommended for general office printing in Windows environments and designed specifically for HP PageWide printers. Provides the overall best speed, print quality, and product-feature support for most users. Install from the printer CD or download from
    HP UPD Postscript driver Recommended for Adobe and other graphics-intensive software. Provides the best PostScript emulation and handling of PostScript fonts. Download from
    HP UPD PCL 6 Recommended for printing across most network and server environments. Best option for administrators to configure and manage the printer. Download from

    You May Like: What Hp Printers Use 950 Ink

    How To Clean An Hp Deskjet Printer

    If you regularly print documents for your business, you’ll need to perform frequent maintenance to keep your printouts sharp and clear. Over time, dried ink and dust can clog the ink nozzles and cause streaks or blank spaces on the paper. HP Deskjet printers have a built-in process that cleans dried ink from inside the cartridges, which may eliminate missing lines or dots on your printouts. If you notice ink streaks after printing, you’ll need to manually clean the cartridges to remove any external debris.

    Printer Skipping Lines: Why It Happens How To Fix It And Tips To Prevent It Happening Again

    When a printer is skipping lines, it isnt much use to anyone. You click print on your document or photo, and you get an unusable mess with the printer not printing all the lines.

    Sometimes the printer only prints every other line. Sometimes, it is skipping lines seemingly at random. However your printer is acting up, you need to understand the problem and find a quick fix.

    When your printer skips lines while printing, this is what it looks like.

    A printer skipping lines is a common issue across manufacturers. But whether youve got an HP printer missing lines when printing, an Epson printer not printing every line, or a Canon printer skipping lines, youve come to the right place.

    Well take you through the common causes for why your printer is skipping lines, a list of possible solutions, and tips for avoiding this frustrating problem in the future.

    Don’t Miss: Connecting Phone To Wireless Printer

    Solution 3 Printhead Alignment Using Hp Deskjet Toolbox

    Follow the steps given below to align the cartridges for solving HP printer missing lines:

    • Launch the HP Deskjet toolbox.
    • In the toolbox, click Printer Services.
    • Tap Cartridge Alignment and follow the screen instructions.

    Perform a Cartridge Cleaning from the toolbox:

    • Double-click the HP Deskjet Toolboxicon on the desktop.
    • Tap Clean the Print Cartridges and follow the instructions.

    Troubleshooting tools

    HP Printer Assistant It is a printing software that comes with HP printers made after 2009. It helps to set up your printer and check ink levels. To fix the error HP printer missing lines, you can also align and clean the cartridges by using this tool:

    • Launch the Printer Assistant.
    • Navigate to Printer Maintenance.
    • Tap Calibrate and follow the instructions displayed on-screen.

    After completing the alignment process, go ahead with cartridge cleaning:

    • Go to the Printer Maintenance option.
    • Select Clean Cartridges.

    HP Scan Doctor It is a free tool for Windows that assists you in dealing with printing and scanning issues.

    Apart from the solutions mentioned above, you can use these tools to help you guide and rectify issues like HP printer missing lines. Be it printing spray lines, color out, missing dots, or color mixing, printing problems can hamper your official work. So, it is better to be equipped with the basic knowledge of tips and tricks to resolve these troubles.

    My Hp Printer Is Printing Black Lines How To Fix Them

    Resolve Streaks When Scanning or Copying Through the Automatic Document Feeder | HP Printers | HP

    Mostly user likes the HP printer due to it has many advances feature for the printing and working with a long time. It prints the document and files with the best quality, scans, fax, and print lots of document with few times. Today HP Printer comes in marking with multifunction or All in one printer. According to this feature, many users purchase for business and home purposes.

    Using for a long time, not a problem facing. But sometimes, users face a problem with the printer is printing black lines. It is the common error, in the HP printer is black lines on the document during printing. Print in the document shows black horizontal lines on the paper. This problem is a printing error so your printing lines on the paper show or not printing well. Contact us today with a toll-free +1-877-614-7218 number and resolve the printer black lines issues.

    Also Check: Why Is My Hp Envy 7800 Printer Offline

    Try Again See If The Problem Goes Away

    Always double check the symptoms of the problem. If some one else has told you what has happened, run a test print of your own. Do your own diagnosis. Sometimes the image problem changes for the better. For example, if a small quantity of toner droppedfrom the toner cartridge due to mishandling, things may clean up after a few prints or so. If the problem remains or worsens, go back to the Image Problem Table for the next step.

    Cleaning The Ink Cartridge Cradle

  • Assume an eye level position with the HP Photosmart printer.
  • Locate the ink cartridge cradle.
  • Using clean, moistened swabs, wipe the underside of each wall of the carriage where fibers may collect and come in contact with the paper. Repeat until no ink residue is seen on a clean swab.
  • Reconnect power cord when finished cleaning.
  • When finished cleaning the ink cartridges and the cradle, print a test page.
  • Recommended Reading: Set Up Wireless Printer On Iphone

    How To Fix Hp Printer Missing Lines When Printing Problem

    When we wish to get our documents printed, all that we expect is a good output with dark text that is clearly visible and legible. HP printer can make our printing job super quick and convenient. But at times there are some printing problems that might bother you like some letters missing, or extra line or markings on the page.

    When you see these flaws, it indicates that there is a problem with your printing material . The error HP printer missing lines when printing is easy to fix using simple procedures. But before you jump to solutions, it is advised to understand the root cause of the problem.

    Create An Account On The Hp Community To Personalize Your Profile And Ask A Question

    HP M553 Prints intermittent black streaks on pages


    HP ENVY Photo 6255 printer is printing everything in a streak manner in that it prints normally but has lines where the ink randomly fades, proceeds as normal, fades again rinse and repeat. Ive already tried to clean the cartridges, aligned the cartridges, and cleaned page smudges but none worked. Ive also checked and the cartridge is half full still and was brand new when this problem began.

    I would start by changing the black cartridge.

    Take a look at step # 8 & 9 in this link.

    Hello, but as I said in my post Ive already tried to clean the cartridges, it did not work. I have printed Diagnostic page numerous times and tried the steps it, and this article say to try. They actually progressively seem to make the streaks bigger.

    I would start by changing the black cartridge.

    03-12-202012:18 AM – edited 03-12-202012:19 AM

    Also Check: Brother Printer Cleaning

    More articles

    Popular Articles