How To Reset Brother Printer Drum

Resetting Drum Life After Drum Replacement On Brother Hl

These steps were performed on a Brother HL-5470DW printer after the drum unit was replaced.

Step 1: Turn on the Brother HL-5470DW.

Step 2: Open the front cover of the printer by pressing the front cover release, then pulling the front cover forward.

Step 3: Press and hold the green Go button for five seconds, until you see a message on the display that says Drum Clear.

You can then close the front cover and return to normal printer operation.

How Do I Resolve The Issue Of Printer 8950dw Drum Reset Errors

benpatrick0Disclaimer:report

There are several issues that may arise after replacing a printers imaging drum unit without resetting the drum counter. Error messages such as Replace Drum, Drum End Soon, Drum Near End, and Drum Stop are just some of the problems you might encounter. To clear the error, of course the only solution you can do is to reset the drum counter.

Here are the instructions on how to perform drum counter resetting on a Printer 8950dw Drum Reset Errors.

Note that you may only reset its counter only after replacing the Printer 8950dw Drum unit with a new one. Do not perform these procedures if the consumable inside your machine is still under good working condition and can still deliver more prints.

Drum counter reset is a very easy task. You may also try the steps below on a different Brother Printer model, like the ones from DCP and HL laser series. Although the control panel from each model may differ, you can still perform the reset.

One quick solution to get rid of the errors stated above is by restarting the printer. Turn it off and unplug it from an outlet, then let it rest for like 10 minutes. After that, turn it back on and see if the error message does not return. If it still persists, refer on the fix below.

Pull the front cover down through the provided handle below the units control panel. You dont have to remove the drum unit, just let it be.

Now from the control panel, locate the button labeled with Clear or Back .

How Do I Fix The Drum On My Brother Printer

If you reset the drum counter during the life of the drum unit currently being used, the remaining drum life will not be displayed accurately.

Read Also: How To Set Up Airprint On Epson Printer

Close The Front Door Of The Printer

Now the only light that should be on is the Ready light. Your drum has been reset.

Amazon Associate Disclosure: As an Amazon Associate I earn from qualifying purchases. This means if you click on an affiliate link and purchase the item, I will receive an affiliate commission. The price of the item is the same whether it is an affiliate link or not. Regardless, I only recommend products or services I believe will add value to Share Your Repair readers. By using the affiliate links, you are helping support Share Your Repair, and I genuinely appreciate your support.

Reset Drum For Brother Mfc

Brother MFC-L2710DW black and white laser printers are designed with the toner and imaging drum as separate parts. The idea is that the drum unit does not have to be replaced as much as the toner.

Other manufacturers design concepts are different and they come as one piece with the toner cartridge.

After the new drum is inserted in the Brother printer, the counter needs to be reset. It is an easy process in five steps. Follow the steps as shown below and this will stop the drum reminder and reset the drum counter.

Imaging drums show all particles that stick to the cylinder, so ensure that you change the drum regularly, about every four toner cartridges. Imaging Drums also have filters and wipers that collect the excess toner. By replacing the drum you are actually cleaning up the printers workspace as well.

The final result will be a fresh clean image of print.

Don’t Miss: Why Is My Brother Printer Not Connecting To My Computer

Brother Drum Reset Instructions

Brother DR 520 Drum reset procedure

To reset: Make sure the machine is turned on and the drum LED is blinking. Open the front cover. Press and hold the “Go” button for four seconds until all the LEDs light up. Once all the LEDs are lit, release the “Go” button. Close the front cover. The counter is reset.

Drum Life Low warning: Drum light blinking, Green Status Light on: Drum life over soonaround 6% life remaining printer does not stop at any point. Status page, if printed, will show 0% life left. End user can continue to use the Drum unit as long as theyre happy with the print quality.

MFC or DCP printers with a LCD display utilizing the DR520 Drum Unit

If the LCD shows Drum Near End, the drum unit is near the end of its life and it is time to buy a new one. Even if the LCD shows Drum Near End, you may be able to continue printing without having to replace the drum unit for a while. However, if there is a noticeable deterioration in the output print quality , then the drum unit should be replaced.

Put the drum unit and toner cartridge assembly back in the machine.

A. Do not close the front cover.

B. Press Clear/Back until you see: Replace Drum?

a 1.Yes

To confirm you are installing a new drum, press 1.

C. When the LCD shows Accepted, close the front cover.

Brother DR 600 Drum reset procedure

Open front cover, press & hold the GO BUTTON UNTIL drum clear is displayed, release button, and close front cover

Brother DR-350 Drum reset procedure

Mfc-7420 w/LCD

Reset The Drum Counter

When you replace the drum unit with a new one, you must reset the drum counter by completing the following steps:

DO NOT reset the drum counter unless you are replacing the drum unit.

Read Also: How To Connect Printer To Computer With Usb

How To Reset Brother Printer Drum

Printer drum reset is a common practice for Brother printers. The printer can run out of ink rather quickly if it isn’t used often, and the drum must be replaced when this happens in order to continue printing.

This guide will help you reset your brother printer’s ink cartridges so that could keep printing without experiencing any issues with the quality or lack of color on paper.

Brother printers are a common household printer and often come with the ability to print in color. However, like any other piece of technology, they will need maintenance from time to time.

One such maintenance task is resetting or replacing your drum unit when it runs out of ink. If you don’t know how this works, our team can walk you through what needs to be done for this relatively simple process that shouldn’t take too long at all.

We offer free phone consultations so call us today if you want help setting up your new printer or troubleshooting an existing one.

Contents

Brother Dr2125 Drum Counter Reset

To reset the Drum unit counter on your Brother HL2140, HL2150N, HL2170W, MFC7340, MFC7440N and MFC7840W printer or multi-function.

Please follow the guide below:

• For HL series printers :
• With the cartridge door open you will see a white button. Press and hold down the white button for about 4 seconds until all the LEDs light up.
• Once all 4 LEDs are lit, release the button.
• When you close the front cover make sure that the Drum LED is now off.

Recommended Reading: How To Trick Printer Ink Cartridge Hp

How Do You Reset The Drum On A Brother Mfc 7840w Printer

How to reset Brother MFC-7840w Drum

How To Reset Brother Mfc

Reset the low toner message for HL Series printers

These steps will help you reset the low toner message:

1. Open front door3. While holding down the GO button, turn printer back on4. When all four LEDs light up release GO button. All LEDs will turn off5. Press the GO button 2 times. The 3 LEDs will light upsolid6. Press the GO button 5 times7. Paper light will be blinking8. At this point the toner end-of-life condition has been reset. Close frontdoor.*Also, just a reminder, timing is important here so dont pause between buttonpresses*

Read Also: What Is Collate Copies

Brother Dr820 Drum Reset Instructions

The Brother DR820 Drum Reset Instructions are for how to reset the drum on a Brother printer. The steps are easy and quick. First, make sure you have access to a power outlet and paper roll or toner cartridge. Next, unplug the printer from the wall and turn it off by pressing and holding down both buttons on the right side of your LCD screen until all lights turn off.

Then take out cartridges in order: black cartridge first, then color cartridge last before removing any other parts such as covers or trays. Lastly press “reset” button at top left corner of your LCD screen with a pencil or pen that is not metal while plugging it back into an outlet for around 5.

What Is The Drum On A Printer Cartridge

The drum puts toner on paper. Inside the drum unit is a roller called the . This roller is charged with static electricity and uses heat and pressure to fuse the toner to the paper.

The brother printer replace drum dr420 unit is an essential part of your machine’s function. So when it goes bad, your printer won’t, well…print. It’s like riding a bicycle with a flat tire.

After you’ve gone through 3 or 4 toner cartridge replacements, the reset drum for brother printer drum unit will usually need to be replaced. This is normal wear and tear for laser printers. In most Brother printers, the drum for brother printer is attached to the toner cartridges.

You May Like: How Do I Connect My Wireless Printer To My Phone

Brother Mfc L2700dw Toner Reset

Resetting the toner on brother MFC l2700 is relatively easier than drum replacement and reset. Please ensure that you follow the steps as under correctly to reset the toner

• To start the process, please ensure that you open the front cover first, and your printers digital screen should show a front cover open message.
• Next, you need to press and hold the ok button for a few seconds.
• Next, you might see your printers screen saying, replace the drum.
• We suggest you not perform any actions on the printers screen rather, type * 0 0 on the keypad.
• Once you have performed the steps mentioned, you have successfully reset your toner. You can now close the front cover!

Related Article

How To Manually Reset Brother Dr

If you have replaced the laser printer drum, you might still see the Replace Drum message. Dont worry, there is nothing wrong with the new printer drum unit.

Printers use page counters to estimate when the drum will need to be replaced again. When you replace the drum, the page counter must be reset manually. Heres how to reset the drum life display.

The following instructions are for these HL printer models: Brother HL-2220, HL-2230, HL-2240, HL-2240D, HL-2242D, HL-2250DN, HL-2270DW

The following instructions are for these DCP printer models: DCP-7060D, DCP-7065 + HL-2280DW

The following instructions are for these MFC printer models and Intellifax models: MFC-7360N, MFC-7460DN, MFC-7860DW, IntelliFAX2840, IntelliFAX 2940

You May Like: How Do I Scan From My Printer To Computer

Buying A New Brother Drum Unit

If youre looking to purchase a brand new brother drum unit to replace your current one. We sell a full range of Brother drums and toners at TonerGiant.co.uk. Simply visit the Brother toner page, navigate to your printer model using the wizard and the correct Brother drum will be listed on the resulting page.

Did it work? What other problems have you experienced like this? Wed love to hear from you! Leave us a comment below or tweet us .

I Am Unable To Reset The Drum Counter Or Drum Life What Can I Do

• Color Laser LED FAX/MFC
• MFC9340CDW

The Brother machine will display a “Replace Drum” message when the machine has printed approximately 15,000 pages. The drums should be replaced as a set in order to maintain print quality.

Unlike the toner cartridges, the drum change is not automatically detected by the machine when they are replaced. The drum counter must be reset manually.

1. Check the remaining drum life:

b. Press All Settings on the touchscreen.

c. Swipe up or down or press the UP or DOWN ARROW key to display “Machine Info”. Press Machine Info.

d. Press Parts Life.

e. The remaining life of the black drum unit is shown on the display. Because of the manner in which the machine forms images, the other drum units should have the same life remaining.

f. Press HOME

– If the life remaining on the drum units are 0% and the drums have been replaced, the drum counts should be reset in order for the machine to properly track the use of the drum units. Go toSTEP 2.

– If the life remaining on the drums is greater than 0%, you are encouraged to use the existing drum units until the machine no longer prints for maximum use from the drums. At that time, the drums should be replaced.

2. Reset Procedure:

NOTE TO REP:Print quality issues or machine damage may result from using the drum units past their rated life. The drum counter should never be reset without replacing the drum units.

a. Press thered Xon the control panel to interrupt the error.

Don’t Miss: My Ricoh Printer Is Offline

Check You Have Installed The Toner Correctly

Do a simple check to install the toners correctly in the printer. Make sure the toner is correctly sitting in the drum unit and that the drum unit is seated correctly in the printer.

A simple reset is open cover the printer and turn off the printer. Remove all the Brother toner cartridges out of the printer. Wipe and check the chips to see if they are all correct on the toner and havent been dislodged.

Give the printer a quick wipe and clean with a lint free or dust free cloth. Then reinstall the toner cartridges in order with the black cartridge last. Turn your printer back on.

Why Do I Need To Replace The Drum In My Printer

drumneed replacingprinterdrumdrum

Celio Torreira

If you reset the drum counter during the life of the drum unit currently being used, the remaining drum life will not be displayed accurately.

Recommended Reading: How To Uninstall Printer Drivers

S For Replacing Drum On Brother Laser Printer:

Reset Dr420 For Brother Hl Printer Models

HL-2220, HL-2230, HL-2240, HL-2240D, HL-2242D, HL-2250DN, HL-2270DW,

Also Check: Where Is The Wps Pin Located On My Hp Printer

What Does Replace Drum Mean

A drum unit is a maintenance item for your Brother printer that will sometimes need to be replaced but not as often as a toner cartridge.

A drum unit is a green metal cylinder or tube that carries a static electrical charge that attracts the toner powder from the toner cartridge and applies it to the paper as it passes through the printer. Therefore, you will always find that drum unit is located very close to or even attached to the toner cartridge.